Work orders: from release to completion

Reserving material, issuing or backflushing it, reporting output and closing.

Baca dalam Bahasa Indonesia

On this page
  1. The life cycle
  2. Issuing material: pick or backflush
  3. Reporting output
  4. What it does to the ledger
  5. Good habits on the floor
  6. In Voltrus
  7. Checklist

A work order (also called a production order, or perintah kerja) is the instruction to make a quantity of one item by a date. In a spreadsheet factory, production is tracked on a whiteboard and material is taken from the store "as needed". At month end nobody can say how much steel went into last week's cabinets, and the stock count is always short.

The work order fixes that by making production a document with a life cycle. Material leaves the store against a work order, output enters stock from a work order, and the cost of both is collected on it. When it closes, you know what that batch really cost.

The life cycle

StatusWhat it meansWhat happens in the system
DraftPlanned, not yet committedNothing reserved; quantity and date can change
ReleasedApproved for the floorBOM version pinned, routing copied, components reserved
In progressWork has startedMaterial issued, output reported, operations completed
DoneFinishedRemaining output received, leftover reservations freed, cost closed
CancelledAbandonedReservations freed; any value still in WIP written off

Release: the commitment point

Release is where planning becomes a promise to the floor. Good practice is to release only what can actually be built:

  • Material availability check. On release, the system computes the components needed (BOM quantity × order quantity, scrap included) and checks that free stock covers them. If not, release is refused, unless the planner deliberately releases short, knowing a purchase arrives before the material is needed.
  • Reservations. The components are reserved for this order. Reserved stock is still on hand, but it is no longer available to promise to another order. Available = on hand − open reservations.
  • Pinning. The BOM version and the routing are fixed on the order, so a design change tomorrow does not alter what this batch consumes.

Issuing material: pick or backflush

There are two ways to record what production consumed, and most plants use both:

  • Manual issue (pick list). The store picks the components and posts the issue against the work order. Best for expensive, lot-tracked or variable-usage material, because the actual quantity is recorded.
  • Backflush. The system issues components automatically when output is reported: 24 screws per cabinet reported, 24 screws issued. Best for cheap, high-volume items where counting each pick is not worth the effort (screws, labels, packaging).

Material that comes back unused is returned to stock against the same order, so the order is not charged for it.

Reporting output

Long orders should not wait until the end to put finished goods into stock. Report completed quantity as it is made:

  • each report receives that quantity of the finished item into stock (with its lot or serial numbers if the item is tracked);
  • backflushed components are issued in proportion to the quantity reported;
  • labour and overhead for the share of the routing are absorbed into the order's cost.

When the last units are reported, the order is marked done. If the batch came in short, close it with what was made; the system will not let you report more than the order quantity. Over-production needs a new order, which keeps planned and actual quantities honest.

If a quality plan applies at production, reported output goes to a hold warehouse until it is inspected, exactly as at goods receipt. See Lots, serials and quality inspection.

What it does to the ledger

Production runs through a work in progress (WIP) account, an asset that holds value while it is neither raw material nor finished goods:

EventDebitCredit
Issue 75 kg steel at Rp 18,000WIP 1,350,000Inventory 1,350,000
Operation completed (labour)WIP 130,000Applied labour 130,000
Operation completed (overhead)WIP 195,000Applied overhead 195,000
Output 50 cabinets at item costInventoryWIP
Close: remaining WIP balanceProduction varianceWIP

At close, whatever is left in WIP (actual cost minus the value of what was produced) goes to production variance, so a closed order leaves nothing behind in WIP. Why that variance exists and how to read it is in Product costing, WIP and variances.

Good habits on the floor

  1. Post at the time of the event. An issue typed in on Friday from paper notes makes stock wrong all week.
  2. Close orders promptly. An order finished but left open keeps value in WIP and reservations on stock.
  3. Return, don't hoard. Material left at the line after an order finishes goes back to the store against that order.
  4. Read the variance. A close with a large variance is a question, not a number to file: wrong BOM, wrong routing time, or waste on the floor?

In Voltrus

Known limits today: there is no field for finished units scrapped during production (record them with a scrap movement and a reason code), and no capacity check on release, so the planner must make sure the work centres can take the load.

Checklist

  • Release only orders whose material is available or confirmed on the way.
  • Decide per component: picked or backflushed, and write it on the BOM.
  • Report output as it is made, not at the end of the month.
  • Close orders within a day of the last output, and review every variance above your threshold.

Run it in Voltrus ERP

Everything in these guides is built in: documents that post to the ledger as they happen, Indonesian tax, MRP and costing, with AI agents that propose and people who approve.

See Voltrus ERP