Installation
MC & FINS Explorer is a native macOS app, not on the Mac App Store. Download the notarized DMG, open it, and drag the app to Applications.
Download
- Free download: dl-mc-fins-explorer.voltrus.id
- Pro licence: $29.99 one-time from the Voltrus Console. Enter the key in Info, then Activate. One key activates one Mac and can be moved.
System Requirements
| Requirement | Minimum |
|---|---|
| macOS | 13 Ventura or newer (Apple Silicon and Intel) |
| Network | An Ethernet or Wi-Fi route to the PLC's IP address. Not needed for the built-in simulator. |
Mitsubishi: enable MC protocol (SLMP)
The PLC only answers MC protocol on a port that is opened for it. Which CPUs: MELSEC iQ-R, Q series, L series and iQ-F (FX5) with built-in Ethernet, or an Ethernet module (QJ71E71, RJ71EN71 and similar).
- GX Works3 (iQ-R, iQ-F): in the module parameters of the Ethernet port, add an SLMP connection in the external device configuration, and set the protocol (TCP or UDP) and the port number.
- GX Works2 (Q, L): in the built-in Ethernet port settings, open Open Setting and add a line with protocol TCP or UDP, open system MC Protocol, and a host station port number.
- Set the communication data code to binary or ASCII. The client must use the same code.
- To write while the CPU is in RUN, enable "Enable online change" (or "Permit writing in RUN") for the port.
- Write the parameters to the PLC and reset or power-cycle it.
| Setting | Values |
|---|---|
| Frame | 3E (most drivers) or 4E (adds a serial number to match responses) |
| Code | Binary or ASCII, as set in the PLC |
| Transport | TCP or UDP, as set in the PLC |
| Port | As set in the PLC; 5000 is common |
| Network / station | 00 / FF for the CPU you are connected to |
Omron: FINS
FINS listens on UDP port 9600 and, on most current units, TCP port 9600. Which PLCs: CJ1, CJ2, CP1L-E, CP1H with an Ethernet option board, CS1 with an Ethernet unit, and NJ/NX with FINS enabled on the built-in EtherNet/IP port.
| Field | What to enter |
|---|---|
| DA1 (destination node) | The PLC's FINS node number. With automatic address conversion this is the last octet of the PLC's IP address (192.168.250.1 is node 1). |
| SA1 (source node) | A node number for your Mac that no other device on the FINS network uses, for example the last octet of the Mac's IP address. |
| DNA / SNA | 0 on a single local network. |
| FINS/TCP | The PLC assigns the client node during the handshake; you only enter DA1. |
On NJ and NX controllers, FINS reaches memory areas (CIO, DM, W, H, EM). Variables must be mapped to an area with an AT specification to be read over FINS.
Address formats
| PLC | Examples |
|---|---|
| Mitsubishi words | D100, W1A (hex), R0, ZR1000, SD0, TN0 (timer value), CN5 (counter value) |
| Mitsubishi bits | M0, X10 and Y20 (hex on iQ-R and Q; octal on iQ-F), B0, L0, F0, SM400, TS0, CS5 |
| Omron words | D100 (DM), CIO 100, W10, H5, A0, E0_100 (EM bank 0) |
| Omron bits | CIO 0.05, D100.03, W10.00 |
Types for the tag table: Bool, Int16, UInt16, Int32, UInt32, Float32, BCD16 and Hex. 32-bit types use two consecutive words.
Troubleshooting
- Mitsubishi times out: check the port number, TCP or UDP, and binary or ASCII all match the PLC's open settings, and that the parameters were written and the CPU reset.
- Mitsubishi end code C059: the command or subcommand is not supported by this CPU or frame. C056: the request goes past the last address of the device.
- Omron does not answer over UDP: check DA1 matches the PLC's node number and that SA1 is not used by another device. A firewall or a different subnet also stops the reply.
- Omron response code 1103: the address is out of range for that area. 0401: the command is not supported by this unit.
- Writes refused: on Mitsubishi, writing in RUN must be allowed for the port; on Omron, some areas are read-only or write-protected in the PLC setup.
Support
Email [email protected] or see the support page. Mitsubishi Electric, MELSEC, iQ-R, iQ-F and SLMP are trademarks of Mitsubishi Electric Corporation; Omron, SYSMAC and FINS are trademarks of OMRON Corporation. MC & FINS Explorer is not affiliated with or endorsed by either company.