Support

Getting help with EtherCAT Explorer

Frequently Asked Questions

Which network ports work?

Any wired Ethernet port the Mac sees: a built-in port, a Thunderbolt or USB Ethernet adapter, or a dock. Wi-Fi does not carry EtherCAT. Connect the cable to the IN port of the first device on the line, usually the coupler or the drive closest to the controller.

macOS asks for my administrator password.

EtherCAT frames are raw Ethernet frames, and macOS lets only administrators send them through /dev/bpf. When you choose Grant access, the app runs one command with your password that gives the admin group read and write access to /dev/bpf until the next restart. If Wireshark's ChmodBPF helper is installed, it already does this at every start and the app will not ask.

Is it safe to use on a running machine?

No. When you connect, your Mac becomes the EtherCAT master, and a line can only have one. Disconnect the PLC or controller from the line first, and stop the machine. Reading the device list, EEPROM, registers and CoE objects changes nothing on the devices; state changes, output writes, SDO writes and register writes do.

Some devices show no answer, or the list stops early.

The scan follows the cable, so a device that does not answer usually means the cable or connector before it, a device without power, or a port plugged into OUT instead of IN. The Registers view shows lost links and RX errors per port, which point to the cable. The simulator lets you see what a pulled cable looks like.

A device will not go to SAFE-OP or OP.

The device refused the state and reports why in its AL status code, shown next to its state. Common reasons are a process data mapping the device does not accept, a missing sync manager setting, or a device that needs distributed clock sync, which this version does not configure. Going up, the app steps through PRE-OP and SAFE-OP, as the devices require.

A device drops out of OP by itself.

Output devices watch the process data cycle, and drop to SAFE-OP when no frame arrives for about 100 ms (their watchdog). A busy or sleeping Mac can pause the cycle long enough. Request OP again; keep the Mac awake and close heavy apps while you run outputs.

How do I test without a network?

Choose Simulator and start the simulated machine: an EK1100 coupler with EL1008, EL2008, EL3102 and EL4102 terminals and two CiA 402 servo drives. The outputs of the EL2008 and EL4102 are wired back to the inputs of the EL1008 and EL3102, so writes come back as inputs. In the Simulator tab you can pull the cable after a device or add RX errors on a port.

My licence key does not work.

Enter the full key as sent, including the dashes. The first activation needs an internet connection so the app can validate the key; afterwards the app works offline. One key activates one Mac. To use it on a new Mac, enter it there and choose to move the licence, or remove the key from the old Mac first. If it still fails, contact support below.

The app does not open.

EtherCAT Explorer needs macOS 13 (Ventura) or later. The download is signed and notarized by Apple. If macOS still shows a warning, right-click the app, choose Open, then confirm once.

Contact Support

Email

For bug reports, device reports, licence issues, or general questions.

[email protected]

Please include:

  • EtherCAT Explorer version
  • macOS version and Mac model (Intel or Apple Silicon)
  • The devices on the line (make and model), and the Ethernet port or adapter
  • The AL status code or error shown, and what the log shows
  • Steps to reproduce the issue

Response Time

We reply within two business days. A full fix for a complex issue may take longer.

Refund Policy

Direct purchases (card via Polar): Contact us at the email above within 14 days of purchase for a full refund. Full details: Refund Policy.

EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany. EtherCAT Explorer is not affiliated with or endorsed by Beckhoff Automation or the EtherCAT Technology Group.